John Deere 4010 Lp Manual
Find great deals on eBay for john deere 4010 lp. Shop with confidence.
This Distributor cap for a 2 Cylinder with a Delco Distributor, Vertical, 12 Volt. Plug connectors on cap are at 90 degrees or 12:00 o-clock and 3:00 o-clock. For Delco distributors up to 1963 on models: A, AR, AO, B, G, M, 40, 50, 60, 70, 320, 330, 420, 430, 440, 520, 530, 620, 630, 720, 730, 1010, 2010, 3010, 4010, 114W, 116W, 323W.
Balers 25, 30, 40, For 1010, 105, 114W, 116W, 12, 2010, 215, 215A, 25, 299, 30, 3010, 320, 323W, 330, 40, 4010, 420, 430, 440, 45, 50, 520, 530, 55, 60, 600, 620, 630, 65, 70, 700, 720, 730, 95, 99, A, AO, AR, B, G, M. (Part No: 1935038) $9.02. Complete remanufactured distributor for John Deere 4010 and 4020 tractors with Delco distributor 1112466 or 112624.
Replaces original part numbers AR11146, AR47947, TY15857. A refundable $80.00 core charge will be added to your invoice. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. Also NOTE: Note that if the core is not a complete and good core, part or all of the core charge will not be refunded. Typically, most cores need a shaft replacement and the cost of the shaft will be deducted from the core charge. This is usually $30.
(Part No: 1112466) $151.71. Complete remanufactured distributor for John Deere 4000, 4010, 4020, 4230 tractors with Delco distributor 1112581, John Deere part number AT416T. A refundable $80.00 core charge will be added to your invoice. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. Also NOTE: Note that if the core is not a complete and good core, part or all of the core charge will not be refunded.
Typically, most cores need a shaft replacement and the cost of the shaft will be deducted from the core charge. This is usually $30 (Part No: 1112581) $157.71. The Ignitor II has many of the same great features that the Ignitor has, but its smarter.
It senses the coil current level and use a powerful micro controller to adjust variable dwell which helps to maintain peak energy throughout the entire RPM range. Senses startup and develops more energy for quicker, easier starting. Current protection shuts down the system, preventing component damage. NOTE: Ignitor II applications can not be used with solid core ignition wires.
You must use carbon core wires which we do not have available. Replaces points and condenser with an electronic module. Use with 12 volt negative ground systems. For tractor models 4010, 4020 with 302, 340 eng., 4020 with 362 eng. (Part No: 91163A) $115.73. Contains points, condenser, and rotor. VERIFY DISTRIBUTOR NUMBER TO ENSURE FIT.
For: A, AN, AH, AR, AO, B, BN, BW, D, G, M, 40, 50, 60, 70, 320, 330, 420, 430, 440, 520, 530, 620, 630, 720, 730, 1010(to 42000), 2010(to 42000), 3010 (to 1E32999), 4010(to For 1010), 105, 114W, 116W, 2010, 215, 215A, 25, 299, 30, 3010, 320, 323W, 330, 40, 4010, 420, 430, 440, 45, 50, 520, 530, 55, 60, 600, 620, 630, 65, 70, 700, 720, 730, 95, 99. For Delco distributor numbers 1112623, 1112577, 1112648, 1112581. (Part No: ATK1DCR) $7.34. This is a 12 volt starter, clockwise rotation, 10 tooth drive, DD Delco 35MT Type. Rotatable DE housing. Note, check clearance on some JD models, may have interference issues on starter motor height when models have drop type manifold is used.
For models 3010, 3020, 4010, 4020, 4030, 4040, 4040S, 4050, 4230, 4240, 4240S, 4250, 4320 Compact Tractor, 4430, 4440, 444C Indust/Const, 444D Indust/Const, 4450, 4520, 4620, 4630, 4640, 4650, 4840, 4850, 500A Indust/Const, 500C Indust/Const, 5400, 544C Indust/Const, 544E Indust/Const, 544G Indust/Const, 570 Grader, 570A Grader, 5720 Forage Harvester, 5820 Forage Harvester, 624E Indust/Const, 643D Feller Buncher, 644C Indust/Const, 644D Indust/Const, 646C Compactor, 690 Excavator, 690A Excavator, 690B Excavator, 693B Feller Buncher, 7020, 740A Skidder, 8430, 8440, 8450, 8640, 8650. Also replaces SE501446. (Part No: SE501444) $213.90.
This 2 Terminal Switch has many applications. It is a heavy duty momentary switch, push for on and release for off. It is rated for up to 35 volts. Uses two screw terminals. The mounting stem is 5/8 inch number 32 thread. It is 21/32 inch over all length. Check measurements before ordering if using as a universal part.
Applications include Ether Switch, Horn Button, Cold Start, Starter Switch and Manifold Heater Switch. Replaces: AR46184, AR47373, AR47374, R39554, R39554. (Part No: R7994) $11.25. Single bearing. Oil pan gasket.
1 set used in 301 CID 6 cylinder gas engine (not for block numbers R40940, R49550); 1 used in 340 CID 6 cylinder gas engine (block numbers R33170, R43330, R40860, R40870 only, to SN# 200999); 1 used in 381 CID 6 cylinder diesel engine; 1 used in 404 CID & 466 CID 6 cylinder diesel engines (turbocharged & naturally aspirated).For tractor models 4000, 4010, 4020, 4040, 4230, 4250, 4320, 4430, 4440, 4450, 4520, 4620, 4630, 4640, 4650, 4840, 6620, 7020, 7720, 8430, 8440, 8450. (Part No: TP-R71918) $13.49. For 4010, 4020, 600 all with SN. For 4010, 4020, 600, all with SN. For 4010 Gas with block numbers EXCEPT R40940 & R49550 Only. 6 Cylinder - 5 Ring Piston, 301 CID.
Engine Overhaul Kit inludes sleeves and sleeve seals, pistons and rings, pins (1 3/16' O.D. Pins) and retainers, pin bushings, complete gasket set, crankshaft seals, intake and exhaust valves, valve retainers and springs, main bearings and connecting rod bearins. Main and Rod bearings available in Standard,.010',.020', and.030' undersize. Specify bearing sizes when ordering. Kit also available with out bearings as part #EOK1440-LCB. (Part No: EOK1440) $1523.58.
For 4010 DieselGas EXCEPT with block R40930. 6 Cylinder - 3 Ring Piston, 381 CID. Engine Overhaul Kit inludes sleeves and sleeve seals, pistons and rings, pins (1 3/16' O.D. Pins) and retainers, pin bushings, complete gasket set, crankshaft seals, intake and exhaust valves, valve retainers and springs, main bearings and connecting rod bearins. Main and Rod bearings available in Standard,.010',.020', and.030' undersize. Specify bearing sizes when ordering. Kit also available with out bearings as part #EOK4441-3-LCB.
(Part No: EOK4441-3) $1744.53. For 4010 Diesel EXCEPT with block # R40930.
6 Cylinder - 5 Ring Piston, 381 CID. Engine Overhaul Kit inludes sleeves and sleeve seals, pistons and rings, pins (1 3/16' O.D. Pins) and retainers, pin bushings, complete gasket set, crankshaft seals, intake and exhaust valves, valve retainers and springs, main bearings and connecting rod bearins. Main and Rod bearings available in Standard,.010',.020', and.030' undersize. Specify bearing sizes when ordering. Kit also available with out bearings as part #EOK1441-LCB.
(Part No: EOK1441) $1725.48. Marked with casting number R63451, with oil pump gear, with front timing gear, timing gear is installed. Cam Followers Fits: 3020 (SN 280000 4.270), 4000 (SN ), 4050 (SN 335846, 6.466D), 4230 (SN 335845), 4240 (SN 335846, 6.466D), 4250 (6.466T W/ SN 253373, & 6.466A SN 317859), 4320, 4430 (SN 335845, 6.404T/A), 4440 (All 6.466T SN & 6.466A SN ), 4450 (6.466T W/ SN 253373, & 6.466A SN 317859), 4520 (SN, 6.404T/A), 4640 (All 6.466T SN & 6.466A SN ), 4650 (6.466T W/ SN 253373, & 6.466A SN 317859), 4840 (SN 258, 6.466A), 4840 (6.466T SN 4.270) (Part No: R52773) $11.50.
Cam Followers marked R52773 Fits: 3020 (SN 280000 4.270), 4000 (SN ), 4050 (SN 335846, 6.466D), 4230 (SN 335845), 4240 (SN 335846, 6.466D), 4250 (6.466T W/ SN 253373, & 6.466A SN 317859), 4320, 4430 (SN 335845, 6.404T/A), 4440 (All 6.466T SN & 6.466A SN ), 4450 (6.466T W/ SN 253373, & 6.466A SN 317859), 4520 (SN, 6.404T/A), 4640 (All 6.466T SN & 6.466A SN ), 4650 (6.466T W/ SN 253373, & 6.466A SN 317859), 4840 (SN 258, 6.466A), 4840 (6.466T SN 4.270) (Part No: R52773R) $8.00. 2.50' Offset. Size is 1.250' x 2.50' x 44.750' Bar has 1.010' Holes at 1.060 & 2.310 & 4.360 & 7.050 & 9.050 & 12.30 inches.
For 2510 Hi-Crop, Row Crop Wide Swing, 2520 Hi-Crop, Row Crop Wide Swing, 3010 Row Crop, Std Wide Swing, 3020 Rop Crop, Orchard, 4000 Hi-Crop, 4010 Row Crop, 4010 Row Crop with Wide Swing, 4020 Hi-Crop, 4030 Row Crop.An additional $10 shipping charge applies due to weight/size. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. (Part No: RE20662) $205.72. This Hydraulic Pump has 1 1/16' Left inlet, 7/8' Top Inlet, 1 5/8 Right Inlet, 1 1/16' Discharge. Verify measuerments before ordering.
It is used on 1550, 1640, 1750, 1830, 1840, 1850, 1950, 2030, 2040, 2130, 2140, 2155, 2250, 2350, 2355, 2440, 2450, 2510, 2520, 2550, 2555, 2630, 2640, 2650, 2750, 2755, 2840, 2850, 2855N, 2940, 2950, 2955, 300 Indust/Const, 3010, 3020, 3030, 3040, 3050, 3055, 3130, 3140, 3150, 3155, 3255, 3350, 3640, 3650, 4010, 4030, 500 Indust/Const, 5010, 600 Indust/Const, 9950 Cotton Picker, 9960 Cotton Picker, 9965 Cotton Picker, 9970 Cotton Picker. It replaces AR39168, AR90459, AR97872, R39695 (Part No: AR97872) $959.10. 40cm^3, 50cm^3 with serial plate, this kit is used on pumps that require the teflon sealing washer rather than the quad ring with backup washer, pump models EA1, GA1, GH1. For tractor models 2510, 3010, 4010, 5010, 3020, 4020, (5020 SN# up to 0249999), 7020, 7520, 1830, 2130, 2030, 3030, 3130, 4030, 4230, 4430, 4630, 1640, 1840, 2040, 2040S, 2140, 2440, 2640, 2840, 2940, 3140, 4040, 4240, 4440, 4640, 4840, 2350, 2550, 3150, 4050, 4250, 4350, 4450, 2155, 2355, 2555, 2955, 3055, 3155, 3255, 4055, 4255, 4455. (Part No: RE29107) $61.89.
For Row-Crop Models, Left-Hand Fender for: 530, 630, 730, 2010, 2030, 2155, 2350, 2355, 2440, 2510, 2520, 2550, 2555, 2630, 2640, 2750, 2755, 2840, 2940, 2950, 2955, 3010, 3020, 4000, 4010, 4020, 4320, Row Crop Models with Flat Top Fenders. Also replaces AR48873. Rubber Hand Hole Grommets available as number R20759.
THIS ITEM IS SHIPPED TRUCK FREIGHT ONLY. PLEASE CALL 1-800-853-2651 FOR SHIPPING QUOTE. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint.
(Part No: RE13879) $218.72. Fender right hand, for row crop tractors less cab & sound guard body. Tractors: 530, 630 gp (SN# 6300000 & up), 730G&D GP (SN# 7300000 & up), 2010, 2030, 2155, 2355, 2440, 2510, 2520, 2555, 2630, 2640, 2755, 2840, 2940, 2950, 2955, 3010, 3020, 4000, 4010, 4020, 4320.
John Deere 4010 Lp For Sale
For tractors with tire sizes 13.6 x 38, 15.5 x 38, 16.9 x 30, 18.4 x 30, 18.4 x 34. Tractors: 2350, 2550, 2750. Replaces AR20869, AR20870, AR48872, AR48873.Use fender grip R20759.
THIS ITEM IS SHIPPED TRUCK FREIGHT ONLY. PLEASE CALL 1-800-853-2651 FOR SHIPPING QUOTE. Sheet metal parts may or may not come painted as pictured (unless the description states the color). They often come with only a primer coat of paint. (Part No: RE13878) $218.72.
For JD 3010, 3020, 4000, 4010, 4020. Schwartz Complete Axles and mounting Parts WITHOUT HUBS. These Heavy Duty Models do not include hubs and bearings. Use original hubs and bearings from narrow front axle. The Heavy Duty Models are especially adaptable for use with flotation tires.
Width on wide axles are adjustable from 60' to 86'. Additional $ 100 shipping due to the weight of this item 300 lbs. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. (Part No: 22770) $1464.73. Power Steering Pump Shaft.
OEM part number is stamped in spline end of shaft. Used in 49CC (3.3 C. I.) pump, 6 cyl. For JD 300, 400, 401, 646, 646B, 700A, 760, 760A, 2130, 3010, 3020, 3130, 4000, 4010, 4020, 4040, 4040S, 4230, 4240, 4240S, 4320, 4430, 4440, 4520, 4620, 4630, 4640, 4840, 5010, 5020, 6030, 7520, (310, 444, 300B, 302A, 310A, 401C, 440C, 444C, 444CH, 510, 540B, 544C, 640, All IND), (440, 500, 544, 644, All IND (A and B)), (540, 570, All IND (A)), 600 SN# 119000 (Part No: R34348) $81.48. This steering wheel nut fits the following tractor models: 1020, 1520, 1530, 2020, 2030, 2040, 2150, 2240, 2255, 2350, 2440, 2510, 2520, 2550, 2630, 2640, 2750, 2840, 2940, 2950, 3010, 3020, 4000, 4010, 4020, 4030, 4040, 4050, 4230, 4240, 4250, 4320, 4430, 4440, 4450, 4520, 4620, 4630, 4640, 4650, 4840, 4850, 5010, 5020, 520, 530, 6030, 620, 630, 7020, 720, 730, 7520, 820, 830, 8430, 8440, 8450, 8630, 8640, 8650, and 8850. It measures 0.75 inches wide, 0.444 inches tall, and has a 16 NF thread size.
Replaces part numbers: 14H482, 14H798, and 14H904. (Part No: 353435X1) $0.44.
The Felt Retainer is used with ``FW109S wheel bearing kit. 3.160Inch Diameter OD, 3.086 Inch ID, Thru hole 2.06 Inch Diameter, Outer ring Diameter 3.654 Inches, 1.115 Inch Overall height. Measure Before Ordering.
For model applications: A series excluding AN, BW, D, G series 50 adjustable to serial number 5019164 60 series to serial number 6034693 70 series excluding standard to serial number 7011652. For 3010, 3020, 4010, 50, 520, 60, 620, 630, 70, 720, 730, A, BW, D, G. (Part No: D635R) $13.35. Lucas Hub Oil was formulated to stop leaks in steering axles and trailer hubs on heavy duty trucks. It also allows hubs to run on a marginal amount of oil in case of a blown seal or poor maintenance. It is an excellent gear lube for racing or heavy duty applications.
Key benefits slows leaks, prevents downtime, extremely heat resistant, Very long lasting. (Part No: LU10088) $10.56 Electrical System - Don't see the Alternator you need for your tractor? We have many alternators not listed on this website (for tractors 1953 & newer). Just call us at 800-853-2651. Lucas Assembly Lube (4 oz). Designed to be used as an initial lubricant to metal surfaces. It mixes with any oil and will not plug filters.
This product clings to all surfaces and is an excellent rust inhibitor, allowing long term storage for all parts. It is useful wherever tension or torque is applied. Key Benefits are: Use to pre lube camshaft, bearings, lifters and valve train. Prevents seizing, galling and scuffing perfect for engine lding, super slick and tacky, easy to use, excellent rust inhibitor, excellent for long term storage, contains Zinc, Moly and other extreme pressure additives for maximum protection during engine break-in. (Part No: 10152) $5.00 Engine Parts - Valve Overhaul Kits are located in the Engine Overhaul Kits Section (if available for this tractor). NOTE Engine Rings - Don't see the correct ring set for your tractor? Give us a call and ask for a Hastings Ring Set (made in USA).
We need the following information to correctly find the set you need: 1. Engine size & type (Ex: 233 CID Gas) 2. Number of engine cylinders, 3. Cylinder bore size, 4. Number and size of compression rings for each piston (Ex: (2) 3/32'), 4. Number and size of oil rings for each piston (Ex: (1) 5/32'). NOTE Exhaust System.
Lucas Fuel Treatment is formulated for both gasoline and diesel engines, carbureted or fuel injected. It gives your fuel system what it really needs - a blend of super slick oils and additives with a high detergent action that allows the engine to operate at maximum efficiency. Also, it cleans and lubricates the carburetor and injectors and causes the fuel to burn more thoroughly for increased power and less fuel consumption. Lucas Fuel Treatment should definitely be used in vehicles that require leaded fuel because it actually replaces the benefits of lead in gasoline without causing harmful emissions. Use it to pass smog tests. Finally, it totally neutralizes the harmful effects of low sulfur diesel fuel.A powerful blend of oils and additives that contain no SOLVENTS. Designed to increase power and fuel mileage and also lower exhaust emissions through a more complete combustion.
(Part No: LU10003) $10.67. Comes assembled complete with hardware. Easier hookup, spring loaded locking device. Adjustable top link ball bracket. Includes 7/8 inch mounting pins and adapter bushings, 27-1/4 inches width, 3-1/2 inch x 3-1/2 inch beam. This is ONLY for tractors that have, a three point hitch already installed. An additional shipping charge of $60 will apply due to the weight of this item.
IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. (Part No: HF141101) $227.70. Tail wheel and hub assembly with grease fitting and fork assembly. Shaft on Yoke is 1-1/2 inch diameter, 8 inches overall length, 7-1/4 inches to pin hole.
New style tail assembly, used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405. Wheel must be attached to fork. For Bush Hog cutters with SPB40 spacer (included), assembly will also replace all models with Timken bearings. (Part No: 12269) $176.32. Tail wheel and hub assembly with grease fitting and fork assembly.
Shaft on Yoke is 1-1/2 inch diameter, 8 inches overall length, 7-1/4 inch to pin hole. New style tail assembly, used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405. Wheel must be attached to fork. For Bush Hog cutters with SPB40 spacer (included), assembly will also replace all models with Timken bearings.
(Part No: 12269) $176.32. Tail Wheel and Hub Assembly with grease fitting. 4 x 8 inch rim, 15 inch outside diameter of wheel. Includes wheel, hub, axle bearing and bolt assembly.
OLD style tail assembly used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. Wheel must be attached to fork. For Bush Hog cutters.
With SPB40 spacer, assembly will also replace all models with Timken Bearings (Ref #1-#11). (Part No: BH215) $106.08. 6 inch x 9 inch tail wheel assembly with laminated tire, less hub.
4 inch pilot, 5 bolt holes, 5-1/2 inch bolt circle. 5-1/4 inches wide, 21 inch outside diameter, 74#.
Used mostly on pull Bush Hog models of the following series mowers: 109, 115, 126, 160, 166, 205, 206, 207, 220, 255, 256, 257, 268, 305, 306, 307, 310, 315, 405, 406, 502, 600, 1109, 1115, 1126, 1206, 1207, 1209, 1220, 1226, 1257, 1305, 1306, 1307, 1310, 1315, 1405, 1406, 1600, 2315, 2415, 2510, 2512, 2610, 2614, 2615, 3108, 3209, 3368, 3414, 3610, 4214, 4215, 12610, 12615, 13710, CR14R, CR20F. (Part No: 294) $124.93. 60 inches wide x 65 inches long, molded from virtually indestructible flexible U.V.
Stabilized polyethylene, exclusive socket mounting system for torsion bars, no mounting bolts pass through molding. Available in green, white, orange, blue, or red. Please specify in comments section which color you need.
Hardware to mount to your ROPS sold separately. Additional $150.00 shipping due to weight and size. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED.
(Part No: B257X) $430.31. 45 inches wide x 60 inches long. Molded from virtually indestructible flexible U.V. Stabilized polyethylene, exclusive socket mounting system for torsion bars NO mounting bolts pass through molding. Available in white, green, orange, blue, and red please specify in comments section which color you prefer. Hardware to mount to your ROPS sold separately.
Additional $150.00 shipping due to weight and size. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED.
(Part No: B257XSTD) $374.50. Deluxe Umbrella comes with universal mounting bracket. Four spring steel bows are locked into place with individual spring clips, providing ease of operation and a rigid framework. Frame constructed of tubular steel. All metal parts are zinc plated for rust resistance. 54 inch square cover is made of durable polyester material. Each corner is double reinforced.
AVAILABLE IN RED, YELLOW, ORANGE, WHITE or BLUE. State color desired in comments section of order form when ordering.
(Part No: TU56-X) $155.22. A pure petroleum multi-use oil supplement. Controls noise, heat and wear in manual transmissions and differentials.
Number one in the heavy duty and high performance industries. Lucas Oil Stabilizer is a 100% petroleum product formulated to eliminate dry starts and reduce friction, heat and wear in any type of engine. It allows motor oils a higher degree of lubricity which reduces oil consumption and operating temperatures. Use Lucas Oil Stabilizer in gear oil to stop leaks, reduce operating temperatures and increase the life of the gear oil. Since it is pure petroleum. Key Features Increase oil life at least 50% longer, Reduces oil consumption, Eliminates dry starts, Raises oil pressure, and Increases power and miles per gallon. (Part No: LU10001) $15.12 PTO / Driveline.
AB4 series, complete drive shaft assembly with shielding and tractor and implement yokes. 1-3/8 inch 6 spline Q.D.
Tractor yoke. 1-3/8 inch round bore with 1/2 inch pin hole implement yoke. 1300 mm (51 inch) overall length end of yoke to end of yoke. 1110 mm (43-3/4 inch) compressed length center to center of cross bore. Cross and bearing kit, 27 mm 1.063 (1-1/16 inch) bearing diameter x 74.6 mm 2.940 (2-15/16 inch) overall length (43-3/4 inch). Verify length before ordering.
(Part No: AB4111WY) $187.82. AB4 series, complete drive shaft assembly with shielding and tractor yoke, ratcheting torque limiter on implement end. 1-3/8 inch 6 spline Q.D.
Tractor yoke, 1-3/8 inch 6 spline ratcheting torque limiter with quick disconnect on implement end. 1372 mm (54 inch) overall length end of yoke to end of clutch. 1110 mm (43-3/4 inch) compressed length center to center of cross bore. Cross and bearing kit 27 mm 1.063 (1-1/16 inch) bearing diameter x 74.6 mm 2.940 (2-15/16 inch). 1372 mm (54 inch) overall length.VERIFY LENGTH BEFORE ORDERING. (Part No: AB4111K33) $288.01. Universal Application Leatherette Suspension seat.
For most Compact, Agricultural and Industrial Tractors. Adjustable base for 5 different mounting angles, Internal Suspension Weight Adjustment, Special Slotted Base for mounting holes adjustments of approximately 2-1-2 inches forward/rear, Adjustable Slide Track. IMPORTANT: THESE SEATS FIT MOST TRACTORS, BUT NOT ALL. PLEASE LOOK CLOSELY AT THE DIMENSIONS ON THE PICTURE BEFORE ORDERING TO BE SURE IT WILL FIT YOUR TRACTOR. Color is Black. Additional $30 shipping due to size and weight. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED.
(Part No: TS1050ATSP) $82.25. BLUE Universal application leatherette suspension seat. For most compact, agricultural and industrial tractors. Adjustable base for 5 different mounting angles, internal suspension weight adjustment, special slotted base for mounting holes adjustments of approximately 2-1-2 inches forward/rear, adjustable slide track.
IMPORTANT: THESE SEATS FIT MOST TRACTORS, BUT NOT ALL. PLEASE LOOK CLOSELY AT THE DIMENSIONS ON THE PICTURE BEFORE ORDERING TO BE SURE IT WILL FIT YOUR TRACTOR. Color is BLUE. Add $15 additional shipping per seat due to size and weight. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. (Part No: TS1060ATSP) $89.37. Universal Application Leatherette Suspension seat.
For most Compact, Agricultural and Industrial Tractors. Adjustable base for 5 different mounting angles, Internal Suspension Weight Adjustment, Special Slotted Base for mounting holes adjustments of approximately 2-1-2 inches forward/rear, Adjustable Slide Track. IMPORTANT: THESE SEATS FIT MOST TRACTORS, BUT NOT ALL. PLEASE LOOK CLOSELY AT THE DIMENSIONS ON THE PICTURE BEFORE ORDERING TO BE SURE IT WILL FIT YOUR TRACTOR. Color is BLACK. (Part No: TS1075ATSP) $82.25.YELLOW.
John Deere 4010 Lp
Universal Application Leatherette Suspension seat. For most Compact, Agricultural and Industrial Tractors. Adjustable base for 5 different mounting angles, Internal Suspension Weight Adjustment, Special Slotted Base for mounting holes adjustments of approximately 2-1-2 inches forward/rear, Adjustable Slide Track. IMPORTANT: THESE SEATS FIT MOST TRACTORS, BUT NOT ALL. PLEASE LOOK CLOSELY AT THE DIMENSIONS ON THE PICTURE BEFORE ORDERING TO BE SURE IT WILL FIT YOUR TRACTOR. Color is John Deere Yellow. Add $15.00 additional shipping due to weight.
IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. (Part No: TS1040ATSP) $88.39 Sheet Metal / Body Parts. This Power Steering Pump replaces the Eaton style belt driven Power Steering Pump.
It also replaces Eaton part numbers: 503-1005-005, 20928 and P761. This is a Redesigned Pump that uses a bearing instead of original bushing. It can also be adapted to tractors using Char-Lynn power Steering with an Eaton Pump. Please note that this pump does not include brackets, top mounted reservoir, or pulley. Some applications will require a new pressure hose to be made for a 5/8-18 inch inverted flare type fitting.
The shaft diameter measures.670 inches. The shaft length, where the pulley mounts measures.575 inches. There is a 2 inch thick pump housing where the bracket bolts on. Pressure is preset at 1.32 GPM. (Part No: S03-1003) $384.33. Front Tire, 3 Rib, 6.00 inches x 16 inches. Designed to be used with tube (part number WHS050).
Additional $25 shipping due to size and weight. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED.
(Part No: 600X16) $63.35 Tractor Manual Search - Yesterday's Tractor Co. Manuals If you will be servicing or maintaining your tractor, we highly recommend that you have a manual to refer to. We searched the tractor manual database and found the following items. They may or may not apply to your tractor, please read the descriptions carefully. Our search engine isn't perfect. John Deere Model 4010 Manuals I&T Aftermarket Shop Repair Manual 224 Pages (Part No: JD-203) $29.95 Service Manual 740 Pages (Part No: JD-S-SM2039) $119.95 Parts Manual 504 Pages (Part No: JD-P-PC691) $54.95 Operators Manual 84 Pages (Part No: JD-O-OMR32129) $29.95 Parts Manual 238 Pages (Part No: JD-P-PC737) $39.95 Miscellaneous Related Items Tune-up DVD.
With embroidered John Deere logo. (Part No: JDGR) $19.95 Call 800-853-2651 to Order Or Click the 'Add to Cart' Button Customer Service Monday - Friday 9:00-6:30pm EST Order online anytime! Your Shopping is YESTERDAY's TRACTORS has been a leading tractor parts supplier on the internet since 1995. Join thousands of happy customers who have purchased parts and more for their antique tractor from us! Copyright © 1997-2018 Yesterday's Tractor Co. Antique Tractor Headquarters All Rights Reserved TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. Products and within the Yesterday's Tractor Co.
Websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.